Canon iR3570 Series, Руководство по обслуживанию

Страница: 604 / 722

Chapter 15
15-16
15.3 Error Code (SEND)
15.3.1 Results of Self-Diagnosis
0008-0278
iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N / / iR4570N / iR2230 / / iR3530 /
T-15-8
0004 An attempt to switchover to a language on the HDD fails. Download a language file of the correct version.
1000 The boot ROM that is mounted is of the wrong type. Replace the boot ROM with one of the model in question.
2000 The engine ID indicated by the software ID is illegal. Replace it with a software ID of the correct model.
E745 There is a fault on the TokeRing board.
0001 An attempt at PCI initialization has failed. 1. Disconnect and then connect the TokeRing board.
2. Replace the TokeRing board.
0002 The MAC address is faulty. 1. Replace the TokenRing board.
0003 There is an error in the acquisition/setting of board information. 1. Replace the TokenRing board.
0004 There is a connection error. 1. Check the connection of the cable.
2. Replace the cable.
3. Check the power source of the MAU.
4. Replace the MAU.
5. Replace the TokenRing board.
0005 Other Errors
E746 The accessories board is of the wrong type.
0003 At startup, a board for a different model has been detected. Replace the UFR board of the correct type (model).
E748 There is a mismatch between controller board and SDRAM size.
1001 There is a mismatch between the control board and the SDRAM. Check the correct combination between board and SDRAM.
E805 There is a fan error.
0000 While the fan is at rest, the lock signal has been detected for 5 sec.
While the fan is in operation, the lock signal is not detected for 5 sec.
Replace the fan. Replace the DC controller PCB.
Cause Remedy
There is a shortage of TCP/IP resources. Try again later.
While continuous transmission is under way or has
ended in FTP or Windows (SMB), a shortage of TCP/IP
resources has occurred, not permitting reference. Wait a while; then, try again.
Set the IP address.
The IP address of the machine has yet to be set. In user mode, set the IP address; thereafter, turn off and
then on the machine.
The server does not respond. Check the settings.
The settings of the selected server are not correct, or the
server has not been turned on. Or, there may be a
shortage of resources. Wait a while; then, try again. If browsing is still not
permitted, select a different server.
NetWare is in use. Try again later.
NetWare is printing using PSeve or NDSPServer, not
permitting browsing. Wait until NetWare finishes printing; then, try again.
The layer in question at the target is too deep to browse.
The number of characters is in excess of the number
allowed. The layer in question cannot be specified. Specify a
different address.
There is no response.
The server is not ready for file transmission. Check the target.
The network is cut for file transmission. (An attempt to
connect to the target of transmission may have failed, or
there is an open circuit in the middle.) Check the network.
The tree name is not specified for NetWare
transmission. Type in the tree name.
An error has occurred for TCP/IP in the course of e-mail
or i-fax transmission. Check the condition of the network cable and the
connector.
Check TCP/IP.
The machine's TCP/IP is not in operation. In user mode, check the TCP/IP settings (IP address,
DHCP, RARP, BOOTP).
The selected server cannot be found. Check the settings.
The IP address in question cannot be identified. 1. In user mode, check the DNS settings.
2. On the DNS side, check the DNS data settings.
If the login information for the LDAP server is set to
'use (security authentication)', the host name in question
cannot be identified. In user mode, check the TCP/IP settings (DNS settings).
The selected server cannot be connected. Check the settings.
Code Cause Remedy