Canon iR3570 Series, Руководство по обслуживанию

Страница: 599 / 722

Chapter 15
15-11
*4 01 The ongoing write operation has been
suspended (at startup). 1. Set '0' for TYPE-TYPE, and execute HDD-
CHECK (40 to 50 min). Thereafter, turn off and
then back on the power.
2. If the symptom still exits after the foregoing,
execute HDD-CLEAR using TYPE-TYPE=1, 2, 3,
5. Thereafter, turn off and then back on the power.
*5 02 A file system error has occurred. 1. Type in TYPE-TYPE of the partition in
question, and execute HDD-CLEAR. Thereafter,
turn off and then back on the main switch.
2. If the system still exits after the foregoing,
suspect a fault on the HDD, and replace the HDD
and re-install the system software.
*6 02 There is a file system error. The system software is designed so that the
information in this partition (e.g., address book,
filter) is not deleted inadvertently; i.e., you will not
the able to execute HDD-CLEAR from service
mode.
1. If possible, ask the user to back up the address
book data using the RUI.
2. From service mode, start download mode; then,
execute full formatting using the SST and re-install
the system software (System, Language, RUI).
Thereafter, turn off and the back on the main
power.
*7 02 A file system error has occurred. This type of error is highly rare.
1. Using TYPE-TYPE=1, 2, 3, 5, execute HDD-
CLEAR. Thereafter, turn off and then back on the
power.
2. If the symptom still exits after the foregoing,
suspect a fault on the HDD, and replace the HDD
and re-install the system software.
*8 02 A file system error has occurred. The system software is designed so that a recovery
session will not run for the boot partition unless
you use safe mode in combination with the SST.
1. Start up in safe mode, and execute full
formatting using the SST and re-install the system
software (System, Language, RUI). Thereafter,
turn off and then on the main power.
2. If the symptom still exits after the foregoing,
suspect a fault on the HDD, and replace the HDD
and re-install the system software.
*9 03 There is poor contact of the HDD, or
a v.x Works system error has
occurred. 1. Check the cable and power supply connectors.
2. If the symptom still exits after the foregoing,
start up in safe mode, and execute full formatting
using the SST and re-install the system software
(System, Language, RUI). Thereafter, turn off and
then back on the main power.
3. If the symptom still exits after the foregoing,
suspect a fault on the HDD, and replace the HDD
and re-install the system software.
*10 11,21 The HDD has poor contact. This type of error is highly rare in relation to read/
write operations.
1. Check the cable and the power supply
connectors.
2.If the symptom still exits after the foregoing,
suspect a fault on the HDD, and replace the HDD
and install the system software.
*11 13, 25 The ongoing write operation has been
suspended. There is a likelihood of the presence of damage to
the file data on the HDD (e.g., Box).
1. Set '0' for TYPE-TYPE, and execute HDD-
CHECK (40 to 50 min). Thereafter, turn off and
then back on the power.
2. If the symptom still exits after the foregoing, set
'1' for TYPE-TYPE, and execute HDD-CLEAR.
(In the case of DOSDEV4 or BOOTDEV, execute
formatting and re-installation once again.)
3. If the symptom still exists after the foregoing,
suspect a fault on the HDD, and replace the HDD
and re-install the system software.
*12 10, 12, 14, 22,
23, 24 There is a system error or a packet
data error. The data may be corrupted or there is a software
bug.
1. Start up in safe mode, and execute full
formatting using the SST and re-install the system
software (System, Language, RUI). Thereafter,
turn off and then back on the main power.
2. If the symptom still exits after the foregoing,
suspect a fault on the HDD, and replace the HDD
and re-install the system software.
YY Description Remedy