Canon iR3570 Series, Руководство по обслуживанию

Страница: 553 / 722

Chapter 14
14-25
14.2.2.8 Part Breakage/Detachment
14.2.2.8.1 Toner is not supplied upon installation: Because shutter arm is damaged
0010-4170
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
[ Inspected by Canon Inc. ]
Description
As a result of inspection, it was found that the symptom occurred because the shutter arm that opens/closes the supply mouth of the sub hopper was damaged.
Field Remedy
When the symptom occurs, execute the following service mode to make a test run of the toner feedscrew motor. If operating noise occurs, check the sub
hopper shutter for damage. If no noise occurs, it is thought that the toner feedscrew motor is faulty or that a fault occurs between the connector J3205 and the
DC controller PCB.
[Service mode > COPIER > FUNCTION > PART-CHK > MTR > enter "9" > OK > MTR-OON].
FC5-1265 Shutter
14.2.3 Printing/scanning
14.2.3.1 No Output
14.2.3.1.1 Machine accepts print job but does not run it
0010-4128
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
[ Case in the field ]
Description
In the field, the following occurred: When the LAN cable is temporarily disconnected from a PC, since the machine is receiving a print job from the PC, it
fails to run the job, and moreover, fails to run print jobs that are sent after reconnection of the LAN cable, even if it can accept such jobs.
Field Remedy
On the System Monitor screen, cancel the print job, of which transmission was not completed. This will allow the machine to run print jobs that were sent
after reconnection of the LAN cable. In case that the causal job is not canceled, the machine cancels it 5 minutes later in accordance with the specifications
and starts running the print jobs that are stopped by the causal job.
14.2.4 Network
14.2.4.1 Ping Failure
14.2.4.1.1 Ping failure sometimes occurs
0010-4116
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
[ Inspected by Canon Inc. ]
Description
In the field, Ping failure occurred because the Ping command was executed within 60 seconds after this machine started up. This is because the spanning tree
process performed between switching hubs prevents them from communicating with each other immediately after the machine connects to a switching hub.
Assuming this problem, the startup time (default: 60 sec.) is required to be set up for the purpose of delaying the start of communication between this machine
and a switching hub.
Field Remedy
When the symptom occurs, start the ping command 60 seconds or more after the machine starts up.
- How to start PING command:
User mode > System Settings > Network Settings > TCP/IP Settings > PING Command
- How to change Startup Time:
User mode > System Settings > Network Settings > Startup Time Settings (Settable range: 0 to 300 sec.)
14.2.4.2 Connection Problem
14.2.4.2.1 E291 Error Code: Occurs when upgrading system software using SST
0010-4117
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /
[ Case in the field ]
Description
In the field, the symptom occurred when a PC with the service support tool (SST) was connected to the machine, and then the machine was started up in
normal mode (by turning on the main power switch while pressing the "1" and "7" keys at the same time).
Field Remedy
When the symptom occurs, follow the procedure below.
1. Open the Command Prompt screen on the PC making the following selection [Start > Programs > Accessories > Command Prompt], type "IPCONFIG"
in [C:\ >], press the Enter key, and then, change the setting for "IP Address" and "Subnet Mask" to the following:
- IP Address: 172.16.1.160
- Subnet Mask: 255.255.255.0
Note: Never enter the following addresses in "IP Address".
- 172.16.1.0
- 172.16.1.100
- 172.16.1.255
2. On the Command Prompt screen, type "Ping_172.16.1.110" (the IP address assigned to the machine) in [C:\ >], and press the Enter key. If "Unknown host
172.16.1.110" is displayed, type the correct IP address and make sure that Ping is successful.
3. In the machine, make the following selection [Service mode > COPIER > FUNCTION > SYSTEM > DOWNLOAD] to make sure that the service support
tool screen is opened.
14.2.5 Transmission/fax-related
14.2.5.1 Transmission Problem
14.2.5.1.1 Latter half of image is lost when scanning and sending A3-size original from DF
0009-2432
iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N / / iR4570N / iR2230 / / / iR3530