manualshive.com logo in svg

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 99 / 282

Поделиться
Скачать
Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 99

11.3  Control the Motor

 

WARNING

Ensure  the  enclosure  is  in  place  before  the  device  is  powered  on.  Wait  for  at

least 5 minutes after powering off to allow the DC capacitor being discharged,

and do not remove the cover during this period!

Step

Operation

Description

1

Rotate  the  potentiometer  counterclockwise

(leftwards) to the greatest extent

Output frequency setting is 0.00

2

Press <Run> button

Control command active, 0.00 is displayed

3

Rotate  the  potentiometer  clockwise  (right-

wards) slowly till 5.00 is displayed

The motor starts to run

Observe the running status:
If the motor runs in the correct direction
If the motor runs steadily
If there is any abnormal noise or problem

Recommended operation:
Stop the motor immediately by switching off

the power if any abnormality occurs
Restart  commissioning  only  after  error  cau-

ses have been removed

4

Rotate the potentiometer clockwise

The motor accelerates

5

Rotate the potentiometer counterclockwise The motor decelerates

6

Press <Stop> button

Stop command activated, the motor stops

7

Check parameters without load

Settings according to actual applications

8

Check parameters with load

Settings according to actual applications

Tab.  11-5:   Motor controlling procedure

●

After powering on, VFC 3210 will generate output if pressing down the <Run>

button (or 'Control by terminals' is activated).

●

By default, VFC 3210 is set as:
– The frequency converter is started or stopped by the operating panel.
– The output frequency is set by the potentiometer on the operating panel.

●

After powering on, please confirm:
– The setting frequency is displayed (no error display).
– The monitoring parameter is consistent with the actual situations.

●

By default, Output frequency in run status and Setting frequency in stop sta-

tus are displayed as the monitoring parameters, which can be changed to oth-

er  parameters  with  parameters  U1.00  and  U1.10.  The  default  settings  are

based on standard applications with standard motors.

VFC 3210 

Bosch Rexroth AG

Quick Start

DOK-RCON04-VFC3210****-IT01-EN-P

71/253

Содержание Rexroth VFC 3210



























































































































































































































































































Отзывы:

Нет отзывов