Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 100

Страница: 100 / 282

11.4 Motor Parameters Auto-Tuning

For the applications with higher requirement to control accuracy in V/f control,

motor parameter auto-tuning is necessary.
Check and make sure the following points before auto-tuning:

●

The motor is in standstill and not at high temperature.

●

The power rating of the frequency converter is close to that of the motor.

●

Set C1.05...C1.10 based on motor nameplate data. If the power factor data is

unavailable on the nameplate, keep the default setting of C1.10.

●

Set E0.08 according to motor parameters and actual application conditions.

Set auto-tuning mode and start motor parameter auto-tuning:
Set the following parameter according to the control mode of the frequency con-

verter and the application situation.

Code

Name

Setting range

Default

Min.

Attri.

C1.01

Motor parameter tuning

0, 1

–

Stop

●

0: Inactive.

●

1: Static auto-tuning.

Press the <Run> button on the operating panel to start auto-tuning. In the proc-

ess of auto-tuning, a status code 'tUnE' will be displayed on the operating panel.

When the auto-tuning process is complete, the status code disappears and the

settings of the following parameters will be obtained automatically:

Static auto-tuning

Parameters obtained by auto-tuning

√

C1.12: Motor rated slip frequency

√

C1.20: Motor no-load current

√

C1.21: Stator resistance

√

C1.22: Rotor resistance

√

C1.23: Leakage inductance

√

C1.24: Mutual inductance

Tab. 11-6: Parameters obtained by auto-tuning

Bosch Rexroth AG
Quick Start

VFC 3210

72/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 100 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: