Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 118

Страница: 118 / 282

12.4.2 Select the Frequency Setting Source

General setting
Different frequency setting sources can be selected by setting parameter E0.00

'First frequency setting source' or E0.02 'Second frequency setting source'.

Code

Name

Setting range

Default

Min.

Attri.

E0.00 First frequency setting source

0...21

–

Stop

E0.02 Second frequency setting source

0...21

–

Stop

●

0: Panel potentiometer
The setting frequency is set by adjusting the potentiometer on the operating

panel.

●

1: Panel button
The setting frequency is set by parameter E0.07 'Digital setting frequency'.

Pressing <▼> and <▲> buttons on the operating panel will decrease and in-

crease the output frequency respectively when the frequency converter is run-

ning.

●

2: AI1 analog input
The setting frequency is set by AI1 input.

●

11: Digital input Up / Down command
The setting frequency is set by command of Up / Down / Reset via digital in-

puts.

●

20: Communication
The setting frequency is set by engineering software, PLC or other external

device via Modbus protocol.

●

21: Multi-speed settings
The setting frequency is set by multi-speed settings.

Bosch Rexroth AG
Functions and Parameters

VFC 3210

90/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 118 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: