Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 170

Страница: 170 / 282

12.9.4 PID Regulation Mode Setting

Code

Name

Setting range

Default

Min.

Attri.

E4.30 PID deadband

0.0...20.0 %

2.0

0.1

Run

This parameter is used to set the limit of the deviation between reference and

feedback value. When the difference is within the defined 'PID deadband', PID

control stops to bring a stable output.

Code

Name

Setting range

Default

Min.

Attri.

E4.31 PID regulation mode

0, 1

–

Run

When the PID output reaches [E0.09] 'Output frequency high limit' or [E0.10]

'Output frequency low limit' in PID control, following modes are available for PID

regulation:

●

0: Stop integral regulation when frequency arrives at upper / lower limit
When the difference between the reference values and the feedback values

changes, the integral value follows immediately the difference. When the set-

ting frequency reaches the limits, the integration stops, and the integral value

remains unchanged.
This mode is used in applications with fast change reference values.

●

1: Continue integral regulation when frequency arrives at upper / lower limit
When the PID output reaches the limits, the integral continues up to its possi-

ble numerical limit.
This mode is used in applications with stable reference values. When the dif-

ference between reference and feedback changes, more time is needed to

eliminate the impact of accumulated integral regulation before the integral

value can follow the change in the trend.

Bosch Rexroth AG
Functions and Parameters

VFC 3210

142/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 170 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: