Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 120

Страница: 120 / 282

Frequency setting sources combination
It is possible to combine the two frequency setting sources for complicated ap-

plications.

SRC1

First frequency setting source

SRC2

Second frequency setting source

Set

Setting frequency

Fig. 12-6: Combination of frequency sources

Code

Name

Setting range

Default

Min.

Attri.

E0.04

Frequency setting source combination

0...6

–

Stop

●

0: No combination
By default, actual setting frequency is set by 'First frequency setting source'.

'Second frequency setting source' can be activated by one of digital inputs,

see

chapter "Frequency setting source switching" on page 91

●

1: First frequency s Second frequency setting
The actual setting frequency is the result of the addition operation of the first

and second frequency setting sources.

●

2: First frequency setting - Second frequency setting
The actual setting frequency is the result of the subtraction operation of the

first and second frequency setting sources.

Bosch Rexroth AG
Functions and Parameters

VFC 3210

92/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 120 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: