Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 38

Страница: 38 / 282

and radio equipment in its possible positions of normal use. It might possibly

be necessary to perform a special electromagnetic compatibility (EMC) test.

1.4.4 Protection Against Magnetic and Electromagnetic Fields During

Operation and Mounting

Magnetic and electromagnetic fields generated by current-carrying conductors

or permanent magnets of electric motors represent a serious danger to persons

with heart pacemakers, metal implants and hearing aids.
Health hazard for persons with heart pacemakers, metal implants and hearing

aids in proximity to electric components!

●

Persons with heart pacemakers and metal implants are not allowed to enter

the following areas:
– Areas in which components of the electric drive and control systems are

mounted, commissioned and operated.

– Areas in which parts of motors with permanent magnets are stored, re-

paired or mounted.

●

If it is necessary for somebody with a heart pacemaker to enter such an area,

a doctor must be consulted prior to doing so. The noise immunity of implan-

ted heart pacemakers differs so greatly that no general rules can be given.

●

Those with metal implants or metal pieces, as well as with hearing aids, must

consult a doctor before they enter the areas described above.

Bosch Rexroth AG
Safety Instructions for Electric Drives and Controls

VFC 3210

10/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 38 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: