Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 142

Страница: 142 / 282

Automatic start / stop according to setting frequency
With this function, the converter starts when the setting frequency from analog

input is higher than the threshold, and stops when the setting frequency from

analog input is lower than the threshold. The threshold is set by parameter

E0.41 'Automatic start / stop frequency threshold'.
To use this function, follow the rules below:

●

The frequency setting source should be set to analog inputs.

●

The first and second run command source should be set to '0: Panel'.

Code

Name

Setting range

Default

Min.

Attri.

E0.35 Starting mode

3: Auto start / stop accord-

ing to setting frequency

–

Stop

E0.41 Automatic start / stop frequency

threshold

0.01…[E0.09] Hz

16.00

0.01

Stop

E0.00 First frequency setting source

2: AI1 analog input

–

Stop

E0.02 Second frequency setting source

–

Stop

E0.01 First run command source

0: Panel

–

Stop

E0.03 Second run command source

–

Stop

Fig. 12-22: Automatic start or stop according to frequency threshold

●

When the setting frequency is higher than [E0.41], the frequency converter

starts and runs to the setting frequency automatically.

Bosch Rexroth AG
Functions and Parameters

VFC 3210

114/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 142 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: