Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 113

Страница: 113 / 282

12.2.4 Analog Output Configuration

Step 1: Set AO output mode

Code

Name

Setting range

Default

Min.

Attri.

E2.26 AO1 output setting

0...12

–

Run

E2.28

AO1 value in percentage

from extension card

fieldbus communication

0.00...100.00 %

0.00

0.01

Run

E2.40 Rated voltage

1P 200 VAC: 200...240 V
3P 400 VAC: 380...480 V

220
380

Stop

●

0: Output frequency
Represents the actual output frequency between 0.00…[E0.08] Hz.

●

1: Setting frequency
Represents the setting frequency between 0.00…[E0.08] Hz.

●

2: Output current
Represents the 0…2 x [rated current].

●

4: Output voltage
Represents 0...1.2 x [rated voltage], which is defined by parameter E2.40.

●

5: Output power, represents 0…1.2 x [rated power]

●

6: Analog input, represents AI1 input value

●

12: Parameter setting from communication
– For parameter E2.26, the relationship between the output of '12: Parame-

ter setting from communication' and the communication mode is as follow:
– For modbus mode, the output is defined by register 0x7F06. The value

range of register is 0.00 %...100.00 % (It means percentage of maximum

analog output value).

– For other fieldbus mode, the output is defined by parameter E2.28.

Step 2: Set AO1 filter time and output curve

Code

Name

Setting range

Default

Min.

Attri.

E2.27 AO1 gain

0.0...10.00

1.00

0.01

Run

E2.50 Output curve 1 minimum

0.0 %...[E2.52]

0.0

0.1

Run

E2.51 Output curve 1 minimum value

0.00...100.00 %

0.00

0.01

Run

E2.52 Output curve 1 maximum

[E2.50]...100.0 %

100.0

0.1

Run

E2.53 Output curve 1 maximum value

0.00...100.00 %

100.00

0.01

Run

VFC 3210

Bosch Rexroth AG

Functions and Parameters

DOK-RCON04-VFC3210****-IT01-EN-P

85/253

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 113 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: