BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 84

Страница: 84 / 154

Cleaning

6-2

Cleaning

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

Trimmer

June 22, 2018

CLEANING SOLUTIONS

CLEANING PRIOR TO ASSEMBLY

Prior to assembly, be sure all parts are clean and have been inspected for wear.

PERIODIC CLEANING DURING USE

Remove meat particles and rinse with warm soapy water. Wash the trimmer with warm cleaning
solution. For best results, clean the Quantum Flex

Trimmer with EXTRA© Heavy Duty

Cleaner, diluted according to the directions on the container. Rinse thoroughly with water.

Refer

to Section 7, Cleaning Solution.

CLEANING AFTER DAILY USE

Disassemble and clean thoroughly daily.

Remove the blade and blade housing and clean them with a brush and cleaner. For best results,
clean the Quantum Flex

Trimmer with EXTRA© Heavy Duty Cleaner, diluted according to the

directions on the container. Rinse thoroughly with water and dry.

Refer to Section 7, Cleaning

Equipment

Remove the hand straps from the handpiece.

Refer to Section 5, Remove the Optional Whizard

Micro-Break Hand Straps

. Clean the straps in warm, soapy water.

Before assembly, rinse well with clean water and dry.

NOTICE:

Before reassembling the cam

into the cam plate assembly, spray a small amount of Whiz Lube on each of the two spring
wires on the cam plate assembly.

Refer to Section 5, Cam Installation into the Cam Plate

Assembly - Small Tools Only.

Reassemble the remaining components of the tool.

Refer to

Section 5, Assembly of Handpiece.

CLEANING AFTER BLADE SHARPENING

After sharpening blade, all abrasive dust must be completely removed from the handpiece.
Disassemble the unit and carefully wash each piece with hot, soapy water and a small brush.

NOTICE

Avoid the use of aggressive cleaning products as they will damage the
aluminum handle assembly.

Do not use hydrocarbon solvents on the driveline or casing. This will
cause driveline or casing to shrink in length and become brittle.

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды