BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 41

Страница: 41 / 154

Instructions for Operation

Manual No. 107334

Instructions for Operation

4-9

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

Trimmer

BLADE CHANGING - LARGE TOOLS (CONTINUED)

Blade Installation - Large Tools (Models: X750, X850, X1000,
X1300, X1400, X1500, X1850, X1880)

Turn the tool over so the blade side is up.

Spread open the blade housing with a screwdriver.

NOTE:

A slight tension on the left cover screw will allow the blade housing to stay open on its

own.

•

Insert a new blade in the housing.

•

Loosen the left cover retaining screw so the housing will close.

•

Adjust the housing for proper running clearance. The blade should turn freely with a slight

side-to-side motion. This leaves room for the grease.

WARNING!

Make certain that the blade is free to rotate in the housing. If the blade does not turn

freely, it may cause the tool to rotate in the hand.

•

Tighten the left cover screw to 35 in-lb. (4 N-m). Use of the Bettcher torque wrench kit is

recommended.

•

Re-check the running clearance.

Blade is too tight

•

If the blade is too tight in the housing, adjustments can be made by loosening the left cover

retaining screw and slightly spreading open the housing.

•

Check the housing for proper running clearance and retighten the left cover screw to 35

in-lb. (4 N-m). Use of the Bettcher torque wrench kit is recommended.

Refer to Section 7,

Tools.

"#$

" $

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды