manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 7

Safety 

Manual No. 107334

Safety 

1-3

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

SAFETY SYMBOLS

Symbols are harmonized with ANSI Z535.4 and ISO 3864-2 standards. Warning symbols are presented on a 

safety yellow background. Mandatory action symbols are presented on a safety blue background.

This technical manual is printed in black and white.

The safety alert symbol indicates a potential personal injury hazard. It is 
not used for messages related to property damage. The safety alert 
symbol may be used alone or in conjunction with a signal word in a 
signal word panel 

Danger of electrical shock

Blade hazard, keep hands clear

Read operator's manual 

Protective safety gloves must be worn

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды