BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 37

Страница: 37 / 154

Instructions for Operation

Manual No. 107334

Instructions for Operation

4-5

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

Trimmer

STEELING (CONTINUED)

Steeling For Models:

X350, X440, X500, X500A, X564, X620, X620A

& X750

Be sure to hold the steel at the actual angle of the blade edge. Running the steel at an angle
greater than the factory ground angle will round over the edge and make resharpening more
difficult.

Use the steel lightly and always make the last pass of the steel on the blade on the inside surface
of the blade.

Steeling can be accomplished with much greater consistency with the use of the specially
designed Whizard

Edge Master Steels. For more information contact your Sales Representative

at Bettcher Industries.

Refer to Section 7, Blade Sharpening and Steeling Equipment

Replace or sharpen the blade if this procedure does not improve the cutting action. Blade running
time can be extended with the use of Bettcher

EZ Edge sharpeners. The Bettcher

EZ Edge

allows the operator to sharpen a blade at the work station.

Refer to Section 7, Blade Sharpening

and Steeling Equipment.

The Quantum Flex

Trimmer has been designed in such a way as to allow the blades to be

quickly removed and reinstalled.

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды