manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 56

Maintenance

5-14

Maintenance

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

DAILY INSPECTIONS & MAINTENANCE (CONTINUED)

Whizard Quantum

®

 Driveline Inspection

•

The Whizard Quantum

®

 Driveline includes

a casing and flexible shaft that is factory

lubricated and does not require ongoing

maintenance lubrication.

•

NOTE:

 

The flexible shaft is not removable

from the casing.

•

Inspect the casing for any cracks, tears or

other wear. If any damage is found, replace

the Whizard Quantum

®

 Driveline.

•

Check to ensure that the flexshaft driver can

freely rotate in the casing. If it will not

rotate, replace the entire assembly.

FLEXSHAFT DRIVER

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды