BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 63

Страница: 63 / 154

Maintenance

Manual No. 107334

Maintenance

5-21

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

Trimmer

MAINTENANCE - WHIZARD

FLEXSHAFT AND CASING

ASSEMBLY (CONTINUED)

Inspection of the Driver Assembly

•

Wipe off excess grease.

•

Inspect the split bearing (#5) for wear or

damage. Replace if required.

•

Slide the knurled cap (#6) forward against

the driver tip (#7).

•

Wiggle the bushing (#8) sideways to check

for excessive movement. Movement

should be minimal.

•

Slide the bushing (#8) and washer (#9)

forward toward the driver (#7). If the gap

is 1/16" or greater, the driver should be

replaced.

•

Check the coupling cross pin (#10). If there is any free play or movement, replace the driver

assembly.

NOTE:

The driver assembly for small diameter flexshafts have an “S” marked on the driver tip

(#7).

Installation of the Driver Assembly

•

Clean the threads on the tube and knurled cap.

•

Apply Max-Z-Lube grease to split bearing (#3) and bushing (#2).

Refer to Section 7,

Lubrication and Lubrication Equipment.

•

Apply a small amount of Loctite #242 Threadlocker or equivalent to the threads on the

knurled cap (#1).

•

Pull the spring (#4) on the drive end assembly back with one hand and insert the driver

assembly in the tube.

•

Push in and tighten the knurled cap until it is flush with the end of the tube. Pliers may be

used for this however it is not necessary to tighten beyond hand tight.

•

Allow ½ hour dry time for the threadlocker before the assembly is put in service.

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды