manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 40

Instructions for Operation

4-8

Instructions for Operation

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

BLADE CHANGING - LARGE TOOLS

Blade Removal - Large Tools (Models: X750, X850, X1000, 
X1300, X1400, X1500, X1850, X1880)

•

Hold the tool in your hand.

•

Loosen only the left cover retaining screw (Item #1).

•

With a screwdriver held in the opposite hand, insert the screwdriver in the housing slot

(Item #2). Using the frame as the support point (Item #3), spread open the housing. The

blade should fall out.

NOTE:

 

Some tools have 2 slots in the housing.

NOTE:

 A slight tension on the left cover screw will allow the blade housing to stay open on its 

own.

WARNING

Sharp blades may cause cut injury!

For proper protection of hands, a protective glove should be used when 
operating this equipment and during the handling of blades. Metal mesh 
gloves are recommended for the free hand.

Keep hands away from moving blade.

"

"#$

" $

 

 

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды