BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 74

Страница: 74 / 154

Maintenance

5-32

Maintenance

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

Trimmer

June 22, 2018

ASSEMBLY OF HANDPIECE (CONTINUED)

Blade Installation - Small Tools
Models: X350, X360, X440, X500, X505, X500A, X564, X620, X625,
X620A

•

Turn the tool over so that the blade

housing mounting screws are

pointing upward.

•

Loosen the two blade housing

mounting screws about 1/2 turn if

they are not loose already.

•

Using ¼" nut driver turn the cam

clockwise about 1/8 of a turn until it

locks the blade housing in the open

position.

•

Insert a new blade into the housing.

•

Turn the cam counter-clockwise about

1/8 of a turn to close the blade housing.

•

Tighten the two blade housing

mounting screws.

•

The blade should rotate freely.

WARNING!

Make certain that the blade is

free to rotate in the housing. If the blade
does not turn freely, it may cause the tool
to rotate in the hand.

NOTE:

There is no adjustment in the blade

housing on the small tools.

WARNING

Sharp blades may cause cut injury!

For proper protection of hands, a protective glove should be used when
operating this equipment and during the handling of blades. Metal mesh
gloves are recommended for the free hand.

Be certain that the blade is free to rotate in the housing. If the blade does
not turn freely, it may cause the tool to rotate in the hand.

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды