BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 12

Страница: 12 / 154

Designated Use

2-2

Designated Use

Manual No. 107334

Operating Instructions and Parts List the Quantum Flex

Trimmer

June 22, 2018

DESIGNATED USE

The Quantum Flex

Trimmers are specifically designed for use with the Whizard Quantum

Drive Unit,

Whizard

Ultra Drive Unit and the Whizard

UN-84 Drive Unit. They are used for removal of fat and

tissue, the recovery of lean meat from fat and as a universal cutting tool in the meat industry.

WARNING!

Any use in applications other than those for which the Quantum Flex

Trimmer was

designed and built may result in serious injuries.

MACHINE SPECIFICATIONS

Quantum Flex

Trimmers are highly effective for use in the meat industry, designed with the highest

possible standards for safety, ergonomics and production. These versatile machines, with their carefully

engineered and durable cutting edge, bring uniformity and consistent yield control to all operations. This

Operating Instruction covers the following models:

MODEL

USE

X350

Bone Trimmer

X360

Bone Trimmer

X440

Bone Trimmer

X500

Bone Trimmer

X500A

Bone Trimmer

X505

Defatting Machine

X564

Bone Trimmer

X620

Bone Trimmer

X620A

Bone Trimmer

X625

Defatting Machine

X750

Bone Trimmer

X850

Defatting Machine

X880 (B & S)

Primal Fat Shaper

X1850

Defatting Machine

X1880

Primal Fat Shaper

X1000

Defatting Machine

X1300

Primal Fat Shaper

X1400

Ham Finisher

X1500

Skinning Machine

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды