BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 71

Страница: 71 / 154

Maintenance

Manual No. 107334

Maintenance

5-29

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

Trimmer

ASSEMBLY OF HANDPIECE (CONTINUED)

Grease Cup and Ring

•

Pick up the Quantum Flex

Trimmer.

•

Pick up the grease cup and ring. Apply a small

amount of Whizard Quantum

High Performance

Grease to the frame o-rings.

•

With a twisting motion, install the grease ring onto

the frame over the o-rings.

•

Rotate the grease cup to the desired position.

Optional Thumb Support

•

Pick up a spacer ring or optional thumb

support.

•

If the optional thumb support is used, align the

thumb support splines with the frame splines.

•

The optional thumb support should be located

on the opposite side of the grease cup.

NOTICE

Be careful not to squeeze the
o-rings out of their grooves, or
they could be trapped and
damaged.

GREASE CUP

GREASE RING

FRAME O-RINGS (2)

OPTIONAL THUMB

SUPPORT

FRAME SPLINES FOR

THUMB SUPPORT

THUMB SUPPORT SPLINES

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды