manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 34

Instructions for Operation

4-2

Instructions for Operation

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

OPERATING INSTRUCTIONS

Always hold the handpiece of the Quantum Flex

®

 Trimmer with your thumb extended. Let the 

handpiece rest naturally in the palm of the hand in a relaxed manner. Each person should be 
allowed to hold the handpiece in a position that is most comfortable to them.

The most-used motion is a long sweeping or gliding stroke across the trimming surface. Hold the 
blade surface as flat to the trim surface as possible. A scooping action, such as dipping ice cream, 
should be used around the vertebra.

On flat bones, such as backbones or blades, use a long, quick gliding stroke.

During the cutting operation 

DO NOT

 try to pull the blade out of a cut. Let the blade do the work 

as you would any other cutting tool. Finding the proper angle for the Quantum Flex

®

 Trimmer 

will become easy after experience and use of the tool. 

As with any meat cutting tool, your speed and efficiency is only as good as the blade sharpness.

In order to achieve maximum unit and operator efficiency, it is recommended that sharp blades 
be installed at each shift break. For this reason, it is suggested that extra blades be kept on hand. 
For example, if 4 units are being used and there are 3 shift breaks, 16 blades would be required. 
This would provide a sharp blade for start up and one for each break.

When following this procedure, steeling of the blade is virtually eliminated, and blades need only 
be sharpened once a day. The blade should be stoned or sharpened on a Whizard

®

 Model 210 

Universal Blade Sharpener, Whizard

®

 Model 214 Blade Sharpener, or Bettcher

®

 AutoEdge at the 

end of each work day. 

Refer to Section 5, Blade Sharpening

.

If blades are not changed at each shift break, it may be required to steel the blade. 

Refer to 

Section 4, Steeling the Blade

.

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды