manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 66

Maintenance

5-24

Maintenance

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

ASSEMBLY OF HANDPIECE

Handpiece Bearing Installation - Small Tools

•

Push the handpiece bearing in the frame bore and align the small hole through the bearing

 

wall with the slot in the frame. This will align the correct flat on the bearing with the flat in

 

the frame.

WARNING

Sharp blades may cause cut injury!

For proper protection of hands, a protective glove should be used when 
operating this equipment and during the handling of blades. Metal mesh 
gloves are recommended for the free hand.

Keep hands away from moving blade.

WARNING

Inspection of all parts for excessive wear is critical to ensure proper and 
safe operation. Vibration or lock-up may occur as a result of the use of 
excessively worn parts. Prior to assembly, be sure all parts are clean and 
have been inspected for wear.

NOTICE

Installing the bearing upside down will damage the bearing when 
the cover plate it tightened down.

DO NOT force the bearing in. If it does not go in, check frame and 
bearing for damage or build-up.

 

 

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды