BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 55

Страница: 55 / 154

Maintenance

Manual No. 107334

Maintenance

5-13

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

Trimmer

DAILY INSPECTIONS & MAINTENANCE (CONTINUED)

Cover Plate

•

Look for signs of corrosion or wear on the cover.

•

Pay special attention to the area covering the gear teeth.

•

If the edge of the cover is worn, exposing the pinion and blade teeth, the cover should be

replaced.

Whizard

Micro-Break Hand Straps

•

Inspect the strap for hardening and cracks.

•

If any fibers, cuts, or cracks are showing, the strap should be replaced.

Handle Retaining Knob

•

Inspect for cracks.

•

Make sure spring tension in the metal button is adequate.

•

Make sure the metal button is clean and moves freely.

Frame

•

Inspect the frame surfaces where the housing mounts.

•

Look for corrosion and any nicks or burrs that may prevent proper housing seating.

•

Inspect the housing locating key for damage (Large Tools Only).

•

Inspect frame o-rings for cuts or other damage. Replace if necessary.

Steeling Device - Models: X625, X505, X850, X880, X1850, X1880,
X1000, X1300, X1400 and X1500

•

Inspect the surface condition of the carbide steel. If chipped or cracked it should be replaced.

•

Make sure the steeling device and the plunger are free to move.

•

The plunger and steel should be cleaned and oiled with mineral oil in order to keep free

movement and prevent build-up of dirt.

Depth Gauge / Disc Gauge Clamps - Models: X625, X505, X850,
X880, X1850, X1880, X1000, X1300, X1400 and X1500

•

Inspect the depth gauge / disc for wear or damage.

•

Make certain the depth gauge /disc clamps are not bent.

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды