manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 30

Unpacking and Installation

3-12

Unpacking and Installation

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

ATTACHING WHIZARD QUANTUM

®

 DRIVELINE TO THE WHIZARD 

QUANTUM

®

 DRIVE UNIT

Install Whizard Quantum

®

 

Driveline to Disconnect Body

Insert proper end of the driveline into disconnect 

body. The driveline will latch in place when fully 

inserted into disconnect body.

ATTACHING THE WHIZARD

®

 FLEXSHAFT AND CASING 

ASSEMBLY TO THE WHIZARD

®

 UN-84 OR WHIZARD

®

 ULTRA 

DRIVE UNIT

Install Whizard

®

 Flexshaft and 

Casing Assembly to Disconnect 
Body

Install the flexshaft and casing assembly to the 
motor disconnect by lifting the disconnect collar 
and inserting the adapter end of the flexshaft and 
casing into the disconnect body. It may be 
necessary to rotate the casing assembly to align 
the square drive of the flex shaft with the square 
hole in the motor shaft adapter. Release the 
disconnect collar to secure the casing to the motor 
assembly. The flex shaft/casing assembly should 
swivel freely.

DRIVELINE ASSEMBLY

DISCONNECT BODY

CASING RETAINER

LATCH

 

 

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды