BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 35

Страница: 35 / 154

Instructions for Operation

Manual No. 107334

Instructions for Operation

4-3

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

Trimmer

OPERATING INSTRUCTIONS (CONTINUED)

Optional Disc Gauges for Models:
X850, X1850, X1000 and X1300

Optional adjustable disc gauges are available for
the X1000 and X1300 trimmers.

Refer to Section

7, Service Parts to order

To adjust depth:

•

Hold the handpiece with the blade facing

downward.

•

Turn the adjustment knob clockwise for a

thicker cut, or counterclockwise for a thinner

cut.

NOTE:

Take care not to turn too far as the depth

control hub may disengage from the shaft.

Adjustable Depth Gauge for Models: X880 (S&B), X1880, X1400
and X1500 Only

These tools come equipped with an adjustable
depth gauge for setting a controlled product trim
thickness. The depth gauge can be adjusted for cuts
up to ¼” thick.

A depth gauge setting device is also

available.

To adjust depth:

•

Hold the handpiece with the blade facing

downward.

•

Loosen the attachment screws at the base of

the plastic depth gauge.

•

Adjust the gauge setting by sliding it up or

down to the desired height.

•

Retighten the attachment screws.

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды