manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 10

Safety

1-6

Safety 

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

 June 22, 2018

SAFETY FEATURES

All Quantum Flex

®

 tools have been designed for use with an optional disconnect which will stop 

blade rotation when the trigger/lever is released. This trigger/lever has been designed in such a 
way that minimal grip force is required for operation, using three fingers.

ERGONOMIC FEATURES

Small, Medium, and Large Handle sizes are available to help improve the operator's grip and 
comfort. Fitting the correct size handle to the worker's hand is a very important step. Quantum 
Flex

®

 tools can be configured in both right and left handed configurations. 

Optional Thumb Support - An adjustable thumb support is available to ensure a proper and 
comfortable fit while providing added control and stability of the tool during use. 

Whizard

®

 Micro- Break Hand Strap - This strap has been designed to allow the user to relax the 

fingers between work cycles while maintaining control of the trimmer. This is beneficial to the 
operator to reduce exposure to mechanical stresses. 

NOISE AND VIBRATION LEVELS

Forces applied by the worker are greatly reduced via the drive motor and limited to guiding the 
rotating knife blade.

The noise emission value is less than 79 dB(A)

Vibration of the handpiece is less than 1.1 m/sec2

No negative side effects have been reported

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды