manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 23

Unpacking and Installation

Manual No. 107334

Unpacking and Installation

3-5

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

OPTIONAL THUMB SUPPORT AND HANDLE ADJUSTMENT 
(CONTINUED)

The Quantum Flex

®

 Trimmers have been 

designed to allow the head of the tool and the 
thumb support to be rotated relative to the 
handle. In this way, the tool can be adjusted to 
position the blade properly to the product while 
the handle can be set to allow the operator to 
have a comfortable position for the wrist.

The position which is selected will vary based on 
the individual work station, product, and 
operator. To determine the proper position, it 
will be necessary to observe the operator while 
trying various positions. Select the position in 
which the operator's wrist appears to maintain 
the most neutral position and which is 
comfortable to the operator.

STEP 1

•

Pick up the Quantum Flex

®

 Trimmer.

•

Loosen the handle retaining knob enough to be able to pull the handle back far enough to

disengage it from the frame splines.

STEP 2

•

Pull the thumb support back to disengage it from

the frame splines.

•

Rotate the thumb support to a new position and

push it forward to engage the frame splines.

FRAME SPLINE

FOR THUMB SUPPORT

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды