manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 78

Maintenance

5-36

Maintenance

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

OPTIONAL DISC GAUGE OR DEPTH GAUGE INSTALLATION AND 
ADJUSTMENT (CONTINUED)

Adjustable Depth Gauge for Models: X880 (B&S), X1880, X1400 
and X1500 Only

These tools come equipped with an adjustable depth 
gauge for setting a controlled product trim thickness. 
The depth gauge can be adjusted for cuts up to ¼” thick.

 

A depth gauge setting device is also available. 

•

Slide the depth gauge downward along the cover

plate grooves until the depth gauge clamps catch in

position.

•

The final height adjustment can be made after the

blade is installed.

•

Tighten the two attachment screws.

Adjustment

•

Hold the handpiece with the blade facing

downward.

•

Loosen the attachment screws at the base of the plastic depth gauge.

•

Adjust the gauge setting by sliding it up or down to the desired height.

•

Retighten the attachment screws.

 

 

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды