BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 24

Страница: 24 / 154

Unpacking and Installation

3-6

Unpacking and Installation

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

Trimmer

June 22, 2018

OPTIONAL THUMB SUPPORT AND HANDLE ADJUSTMENT
(CONTINUED)

NOTE:

It may be necessary to rotate the grease cup to a new position to adjust the thumb

support to the desired position.

•

Rotate the handle to a new position and push it forward to engage the frame splines.

NOTE:

The handle can be adjusted to suit the operator and the work station by pulling the

handle back away from the frame and re-locating it on another set of notches on the frame tube.

STEP 3

•

Tighten the handle retaining knob.

Thumb Support Angle Adjustment

• Lift up on the front of the thumb support until

the lug comes out of the notch underneath the

thumb support.

• Rotate the thumb rest to a new position.
• Push the thumb rest back down to seat the lug

into a new notch.

NOTICE

Tighten firmly but take care not to overtighten or the handle will be
damaged.

LIFT UP

LUG

ADJUSTMENT

NOTCHES

THUMB REST

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды