manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 77

Maintenance

Manual No. 107334

Maintenance

5-35

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

OPTIONAL DISC GAUGE OR DEPTH GAUGE INSTALLATION AND 
ADJUSTMENT

Optional Disc Gauges for Models: 
X850, X1850, X1000 and X1300

Optional adjustable disc gauges are available for the 
X850, X1850, X1000 and X1300 trimmers. 

Refer to 

Section 7, Service Parts to order.

•

Slide the disc gauge downward along the cover

plate grooves until the disc gauge clamps catch in

position.

•

The final height adjustment can be made after the

blade is installed.

•

Tighten the two attachment screws.

Adjustment

•

Hold the handpiece with the blade facing downward.

•

Turn the adjustment knob clockwise for a thicker cut, or counterclockwise for a thinner cut.

NOTE:

 Take care not to turn too far as the depth control hub may disengage from the shaft.

 

 

 

  

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды