BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 75

Страница: 75 / 154

Maintenance

Manual No. 107334

Maintenance

5-33

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

Trimmer

ASSEMBLY OF HANDPIECE (CONTINUED)

Blade Installation - Large Tools
Models: X750, X850, X1000, X1300, X1400, X1500, X1850, X1880

•

Turn the tool over so the blade side is up.

•

Spread open the blade housing with a screwdriver.

NOTE:

A slight tension on the left cover screw will allow the blade housing to stay open on its

own.

•

Insert a new blade in the housing.

•

Loosen the left cover retaining screw so the housing will close.

WARNING

Sharp blades may cause cut injury!

For proper protection of hands, a protective glove should be used when
operating this equipment and during the handling of blades. Metal mesh
gloves are recommended for the free hand.

Be certain that the blade is free to rotate in the housing. If the blade does
not turn freely, it may cause the tool to rotate in the hand.

"#$

" $

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды