BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 58

Страница: 58 / 154

Maintenance

5-16

Maintenance

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

Trimmer

June 22, 2018

DRIVER ASSEMBLY INSPECTION AND REPLACEMENT

Whizard Quantum

Driver Assembly Inspection

•

Make certain the driver shaft and tip rotate freely and also that they can slide back and forth

freely.

•

Check for wear on the bearing at the end of the tube assembly. If the bearing flange is

excessively worn, replace the tube assembly.

•

Inspect the flutes of the driver tip. If they are excessively worn, replace the driver tip.

•

Inspect the square end of the driver shaft. If the corners are rounded, replace the driver shaft.

Whizard Quantum

Driver Tip and Driver Shaft Removal

•

Grip the driver shaft tool (Part #101252) in a

vice and place the driver assembly over the tool

so that the square end of the driver shaft fits into

the square hole of the tool.

•

Pull the spring back and use a crescent wrench to

grip the driver tip.

•

Turn the driver tip CLOCKWISE. Continue to

turn the driver tip CLOCKWISE until it is free

from the driver shaft.

•

Pull the driver shaft out of the tube.

NOTE:

Large Tool Models:

X750, X850,

X1000, X1300, X1400, X1500, X1850, X1880 use
a large driver tip.

NOTE:

Small Tool Models:

X350, X360, X440, X500, X505, X500A, X564, X620, X625,

X620A use a small driver tip.

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды