manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 46

Maintenance

5-4

Maintenance

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

DISASSEMBLY OF HANDPIECE

Blade Removal - Small Tools 

Models: X350, X360, X440, X500, X505, X500A, X564, X620, X625, 
X620A

•

Hold the tool in your hand with the blade edge facing upward.

•

Loosen the two blade housing mounting screws about ½ turn.

•

Using ¼" nut driver turn the cam clockwise about 1/8 of a turn until it locks the housing in

 

the open position.

•

Remove the blade from the blade housing.

WARNING

Sharp blades may cause cut injury!

For proper protection of hands, a protective glove should be used when 
operating this equipment and during the handling of blades. Metal mesh 
gloves are recommended for the free hand.

Keep hands away from moving blade.

 

 

 

 

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды