BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 62

Страница: 62 / 154

Maintenance

5-20

Maintenance

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

Trimmer

June 22, 2018

DAILY INSPECTION AND MAINTENANCE - WHIZARD

FLEXSHAFT AND CASING ASSEMBLY (CONTINUED)

Reassemble the Drive End Assembly to a New Casing

•

If using the casing disconnect, place the disconnect lever (#6) onto the lever mounting collar

(#5).

•

Slip the casing latch collar (#2) or lever mounting collar (#5) with disconnect lever (#6)

onto the new casing.

•

Thread the nylon washer (#3) onto the new casing.

•

Clean the threads of the new casing assembly and apply Loctite #242 Threadlocker or

equivalent.

•

Screw the drive end assembly (#4) on the new casing.

•

Tighten by hand and then with a wrench while holding the casing by hand.

Drive End Assembly Inspection and Replacement

Removal of the driver assembly

•

With one hand, pull the spring (#1) back to

expose the knurled cap (#2) at the end of the

tube.

•

Using the other hand, grip the knurled cap

(#2) with a pair of pliers.

•

Using a 7/16" open end wrench, hold the

flats on the drive end assembly (#3) and turn

the knurled cap (#2) counterclockwise.

•

Unscrew the knurled cap (#2) until the

threads are free from the tube.

•

Pull the driver assembly (#4) out of the

tube.

•

NOTE: NEVER use pliers on the tube as

damage to the internal parts may occur.

NOTICE

DO NOT hold the new casing in a vise or use pliers as damage will occur.
It is not necessary to over-tighten this joint.

COMPANY

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Результаты поиска

Содержание Quantum Flex X350

Отзывы:

Бренды по названию

Популярные бренды