manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Инструкция по эксплуатации/Перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Quantum Flex X350 Скачать руководство пользователя страница 73

Maintenance

Manual No. 107334

Maintenance

5-31

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

ASSEMBLY OF HANDPIECE (CONTINUED)

Handle

•

While holding the trimmer, pick up a handle.

•

Firmly push the handle towards the bottom of the

spacer ring or optional thumb support. Align the

handle spline with the splines on the front of the tube.

•

For the initial adjustment position, the arrow on the

handle should be on top 

as shown

.

NOTE:

 

The handle can be adjusted to suit the operator and the work station by pulling the 

handle back away from the frame and re-locating it on another set of notches on the frame tube.

•

Screw on the handle retaining knob by turning clockwise.

NOTICE

Tighten firmly but take care 
not to overtighten or the 
handle will be damaged.

 

  

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex X350



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды