Baldor VS1SD, Инструкция по установке и эксплуатации

Страница: 132 / 192

10-4 PLC Mode Description MN766
ID Description
61 Accelerating - If absolute speed demand is accelerating this condition is True.
62 Constant Speed - If absolute speed demand is constant this condition is True.
63 Decelerating - If absolute speed demand is decelerating this condition is True.
64 At Zero Speed - If absolute speed demand is below the Zero Speed Set Point (P1505) this condition is True.
65 At Set Speed - If absolute speed demand is above Set Speed Point (P1507) this condition is True.
66 Motor Over Current - If motor RMS current is above the Overload Set Point (P1508) this condition is True.
67 Motor Under Current - If motor RMS current is below the Underload Set Point (P1509) this condition is True.
68 Keypad Control - If the drive is under keypad control this condition is True.
69 Dynamic Brake - If the drive's dynamic brake is on this condition is True.
70 Frequency Foldback - If the drive is in frequency foldback this condition is True.
71 Alarm - If an alarm is active this condition is True.
72 Forward - If the drive has a forward command this condition is True.
73 Reverse - If the drive has a reverse command this condition is True.
74
Process PID Error - If the absolute value of Process PID Error is less than the Process PID Error Tolerance (P2606)
this condition is True.
75 Sleep Mode - If the drive's sleep algorithm has put the drive to sleep this condition is True.
76
Comparator A - Monitors a parameter and returns True if the parameter is less than a predefi ned setpoint.
NOTE: See chapter on PLC Comparator Parameters.
77
Comparator B - Monitors a parameter and returns True if the parameter is below a predefi ned setpoint.
NOTE: See chapter on PLC Comparator Parameters .
78 Parameter Table 1 - If parameter table 1 is active then this condition is True.
79 Parameter Table 2 - If parameter table 2 is active then this condition is True.
80 Parameter Table 3 - If parameter table 3 is active then this condition is True.
81 Parameter Table 4 - If parameter table 4 is active then this condition is True.
82 Digital Output 1- If digital output 1 is On this condition is True.
83 Digital Output 2- If digital output 2 is On this condition is True.
84 Relay Output 1 - If relay output 1 is On this condition is True.
85 Relay Output 2 - If relay output 2 is On this condition is True.
86 Timer A - True if Timer A has expired.
87 Timer B - True if Timer B has expired.
88 Less Than (<) - Monitors two parameters (A & B) and returns True if A<B else False is returned.
89 Equal (=) - Monitors two parameters (A & B) and returns True if A=B else False is returned.
90 Greater Than (>) - Monitors two parameters (A & B) and returns True if A>B else False is returned.
91 Timer C - True if Timer C has expired else it is False.
92 Timer D - True if Timer D has expired else it is False.
100 Logical Variable A - Logical variable A is tested for True/False
101 Logical Variable B - Logical variable B is tested for True/False
102 Logical Variable C - Logical variable C is tested for True/False
103 Logical Variable D - Logical variable D is tested for True/False
104 Logical Variable E - Logical variable E is tested for True/False
105 Logical Variable F - Logical variable F is tested for True/False
106 Logical Variable G - Logical variable G is tested for True/False
107 Logical Variable H - Logical variable H is tested for True/False
108 Logical Variable I – Logical variable I is tested for True/False
109 Logical Variable J - Logical variable J is tested for True/False
150 Heater - If the trickle current heater is running then this condition is True else it is False.
Table 10-1 PLC Conditions Continued