Avaya P332G-ML Скачать руководство пользователя страница 75

Страница: 75 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

clear screen

The clear screen command clears the current terminal display.

The syntax for this command is:

clear screen

ping

Use the

ping

command to send ICMP echo request packets to another node on the

network.

The syntax for this command is:

ping

[host[number]]

Note:

You can use this command via the Master switch only.

Output Example:
To ping the IP number 149.49.48.1 four times:

P330-N> ping 149.49.48.1 4

PING 149.49.48.1: 56 data bytes

64 bytes from 149.49.48.1: icmp_seq=0. time=0. ms

64 bytes from 149.49.48.1: icmp_seq=1. time=0. ms

64 bytes from 149.49.48.1: icmp_seq=2. time=0. ms

P330-1(super)# 64 bytes from 149.49.48.1: icmp_seq=3. time=0. ms

----149.49.48.1 PING Statistics----

4 packets transmitted, 4 packets received, 0% packet loss

round-trip (ms) min/avg/max = 0/0/0

host

Host IP address/Internet address of route destination. If missing
then the last host IP is used.

number

Number of packets to send. If missing, then the last number is used.
If the last number is not available, the default is 4.

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды