Avaya P332G-ML Скачать руководство пользователя страница 219

Страница: 219 / 254

Chapter 7

CLI – Layer 3

P334T-ML User’s Guide

201

Example:
To add station 192.168.37.46 as a bootp/dhcp server to handle bootp/dhcp requests
arriving at the interface “marketing”:

Router-N(config-if:marketing)# ip bootp-dhcp server

192.168.37.46

ip bootp-dhcp network Command

Use the

ip bootp-dhcp network

command to select the network from which

the bootp/dhcp server shall allocate an address. This command is required only
when there are multiple interfaces over the VLAN. The

form of this command

restores to the default.

The syntax for this command is:

[no] ip bootp-dhcp network

<ip-address>

Example:
To select the network 192.168.169.0 as the network from which an address shall be
allocated for bootp/dhcp requests:

Router-N(config-if:marketing)# ip bootp-dhcp network

192.168.169.0

ip-address

The IP address of the network.

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды