Avaya P332G-ML Скачать руководство пользователя страница 200

Страница: 200 / 254

Chapter 7

CLI – Layer 3

182

P334T-ML User’s Guide

Example:
To specify simple authentication to be used in RIP Version 2 packets on the interface
“marketing”.

Router(config-if:marketing)#

ip rip authentication mode simple

ip rip authentication key Command

Use the

ip rip authentication key

command to set the authentication

string used on the interface. The

form of this command clears the password.

The syntax for this command is:

[no] ip rip authentication key

Example:
To set the authentication string used on the interface “marketing” to be “hush-
hush”.

Router-N(config-if:marketing)# ip rip authentication key hush-

hush

password

The authentication string for the interface. Up to 16 characters are
allowed.

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды