Avaya P332G-ML Скачать руководство пользователя страница 129

Страница: 129 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

111

The syntax for this command is:

set port negotiation

<mod_num>/<port_num> {enable|disable}

Output Example:
To disable autonegotiation on port 1, module 4:

P330-N# set port negotiation 4/1 disable

Link negotiation protocol disabled on port 4/1.

set port enable

Use the

set port enable

command to enable a port or a range of ports.

The syntax for this command is:

set port enable

[mod_num/port_num]

Output Example:
To enable port 3 on module 2:

P330-N# set port enable 2/3

Port 2/3 enabled.

set port disable

Use the

set port disable

command to disable a port.

The syntax for this command is:

set port disable

<mod_num>/<port_num>

Output Example:

P330-N# set port disable 5/10

Port 5/10 disabled.

mod _num

The switch number

port_num

The port number

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды