Avaya P332G-ML Скачать руководство пользователя страница 148

Страница: 148 / 254

Chapter 6

CLI – Layer 2

130

Avaya P334T-ML User’s Guide

Example:

P330-N> set intelligent-multicast router-port-pruning time 20

Done!

set intelligent-multicast group-filtering delay time

Use the

set intelligent-multicast group-filtering-delay time

command to define group filtering time delays.

The syntax for this command is:

set intelligent-multicast group-filtering-delay time

<time>

Example:

P330-N> set intelligent-multicast group-filtering-delay time

Done!

set security mode

Use the

set security mode

command to enable or disable MAC security at the

stack level. When enabled, the ports are secured based on their individual
configuration. When disabled, all the ports in a stack are non-secured.

Note:

MAC security is not supported in the P330-ML switches. For this reason, this

command does not affect the P330-ML modules. The

set security mode

command is used to enable setting MAC security for ports in other P330 modules in
the stack.

The syntax for this command is:

set security mode

{ enable | disable }

Output Example:

P330-N> set security mode enable

Security mode enabled.

set arp-aging-interval

Use this command to set the ARP table aging interval for gateways’ entries in the
agent ARP table. The MAC value for the default gateway of ML agent in the ARP

time

The time in seconds.

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды