Avaya P332G-ML Скачать руководство пользователя страница 84

Страница: 84 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guide

show port

Use the

show port

command to display port status.

The syntax for this command is:

show port

[<mod_num>[/<port_num>]]

Output Example:
To display the status for port 4 on switch 3:

P330-N> show port

3/4

Port Name Status Vlan Level Neg Dup. Spd. Type

------ ------- --------- ---- ------ ------- ---- ---- -------------

3/4 John connected 1 4 enable half 10M 100/1000Base-Tx

Show Port Output Fields

mod_num

(Optional) Number of the switch. If you do not specify a
number, the ports on all switches are shown.

port_num

(Optional) Number of the port on the switch. If you do not
specify a number, all the ports on the switch are shown.
You can also specify a range of ports separated by a dash, e.g.,
5-13 for ports 5 to 13.

Field

Description

Port

Switch and port number

Name

The name you assigned to the port

Status

Status of the port (connected, no link, disabled, no Rmt Lnk)

VLAN

VLAN ID of the port

Level

Priority level of the port (0-7)

Neg

The autonegotiation status of the port (enable, disable)

Duplex

Duplex setting for the port (full, half)

Speed

Speed setting for the port (10M, 100M.1G)

Type

Port type, for example:
For the P330-ML switches - 100BaseT, 1000BaseT, 1000BaseS.

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды