Avaya P332G-ML Скачать руководство пользователя страница 138

Страница: 138 / 254

Chapter 6

CLI – Layer 2

120

Avaya P334T-ML User’s Guide

Note:

If you wish to define a name which includes spaces, you must enclose the

entire name in quotation marks, e.g. "new york".

set intermodule port redundancy off

Use the

set intermodule port redundancy off

command to clear the

intermodule redundancy scheme.

The syntax for this command is:

set intermodule port redundancy off

set port mirror

Use the

set port mirror

command to define a port mirroring source-

destination pair in the stack.

The syntax for this command is:

set port mirror source-port

<mod_num>/<port_num>

mirror-port

<mod_num>/<port_num>

sampling

{always|disable}

direction

{rx|tx|both}

Output Example:

P330-N# set port mirror source-port 1/9 mirror-port 1/10

sampling always direction both

Mirroring both Rx and Tx packets from port 1/9 to port 1/10 is

enabled

set port spantree

Use the

set port spantree

command to enable or disable the spanning tree

mode for specific switch ports.

always

Keyword to activate the port mirroring entry

disable

Keyword to change the status of the port mirroring entry to “not active”

Keyword to copy only incoming traffic

Keyword to copy only outgoing traffic - Not supported in P330 switches

both

Keyword to copy both incoming and outgoing traffic

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды