Avaya P332G-ML Скачать руководство пользователя страница 240 | Manualshive

Страница: 240 / 254

background image

Appendix B

Specifications

222

P334T-ML User’s Guide

Approved SFF/SFP GBIC Transceivers

The SFF/SFP GBIC (Gigabit Interface Converter) have been tested for use with the
Avaya

P334T

-ML Gigabit Ethernet ports. For a list of approved SFF/SFP GBIC

transceivers, see: www.avayanetwork.com/

Note:

SFF/SFP GBIC transceivers are hot-swappable.

Safety Information

The SFF/SFP GBIC transceivers are Class 1 Laser products. They comply with
EN 60825-1 and Food and Drug Administration (FDA) 21 CFR 1040.10 and 1040.11.
The SFF/SFP GBIC transceivers must be operated under recommended operating
conditions.

Laser Classification

Note:

Class 1 lasers are inherently safe under reasonably foreseeable conditions of

operation.

Caution:

The use of optical instruments with this product will increase eye hazard.

Usage Restriction

When a SFF/SFP GBIC transceiver is inserted in the module but is not in use, the
Tx and Rx ports should be protected with an optical connector or a dust plug.

Caution:

Use only approved SFF/SFP GBIC transceivers. All approved SFF/SFP

GBIC transceivers:
1) Are 3.3V. Do

not

insert a 5V SFF/SFP GBIC.

2) Use Serial Identification. Do

not

use a GBIC that utilizes Parallel Identification.

CLASS 1

LASER PRODUCT

«
...
238
239
240
241
242
...
»

Содержание P332G-ML































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P332G-ML

DGS-1224TP - Web Smart Switch

Бренд: D-Link Страницы: 52

Бренд: D-Link Страницы: 8

DES-3225G Series

Бренд: D-Link Страницы: 3

DES-1228 - Web Smart Switch

Бренд: D-Link Страницы: 69

Бренд: D-Link Страницы: 109

Бренд: Barco Страницы: 2

GenReady Series 005448-2

Бренд: Generac Power Systems Страницы: 4

Бренд: CYP Страницы: 32

Бренд: ASTEK Страницы: 3

HYGRASREG KW Series

Бренд: S+S Regeltechnik Страницы: 16

Premasreg 716 Series

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Kramer Страницы: 2

Бренд: N-Tron Страницы: 169

Бренд: Comtech EF Data Страницы: 70

Бренд: M-system Страницы: 4

Бренд: Quidway Страницы: 43

Бренд: N-Tron Страницы: 157

Бренд: ALFAtron Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды