Avaya P332G-ML Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 254

background image

Chapter 6

CLI – Layer 2

110

Avaya P334T-ML User’s Guide

Output Example:

P330-N# set interface ppp enable

Entering the Modem mode within 60 seconds...

Please check that the proprietary modem cable is plugged into

the console port

Output Example:

P330-N# set interface ppp disable

Entering the Terminal mode immediately

set port level

Use the

set port level

command to set the priority level of a port. Untagged

(without an 802.1p priority header) packets travelling through ports set with
priority 0-3 will be served only

after

packets traveling through ports set with

priority 4-7 in case of congestion. Packets arriving with an 802.1p priority header
will not be modified by this command.

The syntax for this command is:

set port level

[module/port] {value}

Output Example:
To set the priority level for port 2 on module 1 to 7:

P330-N# set port level 1/2 7

Port 1/2 port level set to 7

set port negotiation

Use the

set port negotiation

command to enable or disable autonegotiation

on a port. If autonegotiation is disabled, you can set port parameters using the
relevant CLI commands. If autonegotiation is enabled, these port parameter
commands have no effect. For Fiber Gigbit Ethernet ports, autonegotiation can
determine the flow control (pause) mode only.

Note:

Copper ports in the P332GT-ML can work at 1000Mbps (Full Duplex) only if

autonegotiation is enabled on both cable ends and you are using a 4 pair (8 wires)
Ethernet cable. If autonegotiation is disabled, these ports can only work at 100Mbps
(Full Duplex), and autonegotiation should be disabled on both cable ends.

value

Priority level (0-7)

«
...
126
127
128
129
130
...
»

Содержание P332G-ML































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P332G-ML

Бренд: 3Com Страницы: 8

PathBuilder S200 Series

Бренд: 3Com Страницы: 11

Бренд: 3Com Страницы: 8

CoreBuilder 3500

Бренд: 3Com Страницы: 96

Бренд: Aastra Страницы: 12

Бренд: Aastra Страницы: 2

BNI IOL-314-S52-P012

Бренд: Balluff Страницы: 22

TECMA Silence Marine

Бренд: Thetford Marine Страницы: 9

Бренд: PureLink Страницы: 10

Бренд: Velleman Страницы: 5

Бренд: Eaton Страницы: 120

S5560S-EI Series

Бренд: H3C Страницы: 47

Бренд: Uniclass Страницы: 2

Бренд: Icy Box Страницы: 10

Бренд: hager Страницы: 3

Бренд: cable matters Страницы: 12

Бренд: SMC Networks Страницы: 2

Бренд: LevelOne Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды