Avaya P332G-ML Скачать руководство пользователя страница 155

Страница: 155 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guidee

137

Note:

If you wish to define a name which includes spaces, you must enclose the

entire name in quotation marks, e.g. "new york".

rmon alarm

Use the

rmon alarm

command to create a new RMON alarm entry.

The syntax for this command is:

rmon alarm

rising-threshold

falling-

threshold

<owner>

Output Example:

P330-N# rmon alarm 1026 1.3.6.1.2.1.16.1.1.1.5.1026 60 delta

rising-threshold 10000 1054 falling-threshold 10 1054

risingOrFalling amir

alarm number

This is the alarm index number of this entry (it is advisable to
use the same interface number as your alarm index number.)

variable

This is the MIB variable which will be sampled by the alarm
entry.

interval

The interval between 2 samples.

sample type

This can be set to either

delta

(the difference between 2

samples) or an

absolute

value.

rising threshold

This sets the upper threshold for the alarm entry.

rising event

The RMON event entry that will be notified if the upper
threshold is passed.

falling
threshold

This sets the lower threshold for the alarm entry.

falling event

The RMON event entry that will be notified if the lower
threshold is passed.

startup alarm

The instances in which the alarm will be activated. The
possible parameters are:

Rising, Falling, risingOrfalling

owner

Owner name string.

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды