Avaya P332G-ML Скачать руководство пользователя страница 180

Страница: 180 / 254

Chapter 7

CLI – Layer 3

162

P334T-ML User’s Guide

Example:

Router-1 (super)# sh ip reverse-arp 00:10:a4:98:97:e0

Showing 1 rows

Address MAC Address I/F Type TTL

--------------- ----------------- ----------- ------- --------

149.49.70.68 00:10:a4:98:97:e0 e-70 Dynamic 14355

show ip interface Command

Use the

show ip interface

command to display information for an IP interface.

The syntax for this command is:

show ip interface

[<interface-name>]|<ip-address>|<vlan>]

Output Example:

interface-name

The name of the interface whose information you
want to display.

ip-address

The IP address of the interface whose information
you want to display.

vlan

The name or ID of the VLAN over which there are
interfaces you want to display.

Showing 2 Interfaces

mgmt is administratively up

On vlan Default

Internet address is 10.49.54.14 , subnet mask is 255.255.255.0

Broadcast address is 10.49.54.255

Directed broadcast forwarding is disabled

Proxy ARP is disabled

baba is administratively down

On vlan v2

Internet address is 192.168.0.14 , subnet mask is 255.255.0.0

Broadcast address is 192.168.255.255

Directed broadcast forwarding is disabled

Proxy ARP is disabled

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды