background image

Radio automatic switch 180°

Radio Management 

Radio automatic switch 180°

Art. No. : ..FAS180..

Operating instructions

1 Safety instructions

Electrical equipment may only be installed and fitted by electrically skilled persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.

Keep button cells out of reach of children! If button cells are swallowed, get medical help
immediately.

Risk of explosion! Do not throw batteries into fire.

Risk of explosion! Do not recharge batteries.

These instructions are an integral part of the product, and must remain with the end
customer.

2 Device components

Figure 1

(1) Base plate
(2) Frame
(3) Radio motion detector
(4) Cover

3 Function

System information

By statute, the transmitting power, the reception characteristics and the antenna cannot be
changed.
The range of a radio system from the transmitter to the receiver depends on various
circumstances.
The range of the system can be optimised by selecting the optimal installation location, taking
into account the structural circumstances.

1/8

32552843
J0082552843

16.08.2016

Содержание FAS180 Series









Отзывы: