Avaya P332G-ML Скачать руководство пользователя страница 102

Страница: 102 / 254

Chapter 6

CLI – Layer 2

Avaya P334T-ML User’s Guide

show rmon event

Use the

show rmon event

command to show the parameters of an Event entry

defined by the rmon event command on Page 138 or using the P330 Device
Manager.

The syntax for this command is:

show rmon event

[<Event Index>]

Output Example:

P330-N> show rmon event 1054

event

Event 1054 is active, owned by amir

Description is event for monitoring amir's co

Event firing causes log and trap to community public,last
fired 0:0:0

show ppp session

Use the

show ppp session

command to display PPP parameters and statistics of

a currently active PPP session.

The syntax for this command is:

show ppp session

Example:

P330-N> show ppp session

show ppp authentication

Use the

ppp authentication

command to see the authentication method used

for PPP sessions.

The syntax for this command is:

show ppp authentication

Output Example:

P330-N> show ppp authentication

PPP Authentication Parameters:

------------------------------

Incoming: CHAP

Содержание P332G-ML































































































































































































































































Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды

Avaya P332G-ML, Руководство пользователя

Результаты поиска

Содержание P332G-ML

Отзывы:

Похожие инструкции для P332G-ML

Бренды по названию

Популярные бренды